Garmin Weather Radio 30A XM User Manual

0

Out of 0 Ratings

Owner's of the Garmin Weather Radio 30A XM gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 8
 
4 GDL 30A Installation Instructions
2. Drill
1
/
8
in. (3 mm) pilot holes at the three marked locations.
If you are mounting the GA 32 on berglass, it is recommended to use a countersink bit to drill a clearance counterbore through the top gelcoat
layer (but no deeper). This will help to avoid cracking in the gelcoat layer when the screws are tightened.
3. Use a 1 in. (25 mm) hole saw to cut the cable hole in the center.
4. Place the seal pad on the bottom of the surface-mount bracket. Make sure that the screw holes align.
5. Use the included M4 screws to attach the surface-mount bracket to the mounting surface.
6. Route the cable through the 1 in. cable hole and connect it to the GA 32.
7. Make sure the large gasket is in place on the bottom of the GA 32 antenna, place
the antenna on the surface-mount bracket ➊, and twist it clockwise to lock it in
place ➋.
8. Secure the antenna to the mounting bracket with the included M3 set screw ➌.
9. Route the cable away from sources of electronic interference, and connect it to your
GDL 30A.
Pole Mounting the GA 32 Antenna
With the pole-mount adapter attached to the GA 32 antenna, you can install the antenna
on a standard 1 in. OD pipe-threaded-pole marine mount (14 threads per inch—not
included). You can run the cable through the pole or outside the pole.
To mount the GA 32 with the cable run outside the pole:
1. Route the cable through the pole-mount adapter, and place the cable in the vertical slot along the base of the pole-mount adapter.
2. Thread the pole-mount adapter onto a standard 1 in. OD pipe-threaded-pole marine mount (14 threads per inch—not included). Do not
overtighten the adapter.
3. Connect the cable to the GA 32 antenna.
4. Place the GA 32 antenna on the pole-mount adapter ➊ and twist it clockwise to lock it in place
➋.
5. Secure the antenna to the adapter with the included M3 set screw ➌.
6. (Optional)WiththeGA32installedonthepolemount,lltheremaininggapinthevertical
cable slot with a marine sealant.
7. Attach the marine mount to the boat if it is not already attached.
8. Route the cable away from sources of electronic interference, and connect it to your GDL 30A.
To mount the GA 32 with the cable run through the pole:
1. Position a standard 1 in. OD pipe-threaded-pole marine mount (14 threads per inch—not
included) in the preferred location, and mark the approximate center of the pole.
2. Drill a
3
/
4
in. (19 mm) pilot hole for the cable to pass through.
3.
Fasten the marine mount to the boat.
4. Thread the pole-mount adapter onto the pole. Do not overtighten the adapter.
5. Route the cable through the pole and connect it to the GA 32 antenna.
6. Place the GA 32 antenna on the pole-mount adapter ➊ and twist it clockwise to lock it in place ➋.
7. Secure the antenna to the adapter with the included M3 set screw ➌.
8. (Optional)WiththeGA32installedonthepolemount,lltheverticalcableslotwithamarinesealant.
9. Route the cable away from sources of electronic interference, and connect it to your GDL 30A.
GA 32
antenna
Surface-mount
bracket
Seal pad
Mounting
surface
➊
➋
➌
Rubber
gasket
GA 32
antenna
Surface-mount
bracket
Seal pad
Mounting
surface
➊
➋
➌
Rubber
gasket
GA 32
antenna
Pole-mount
adapter
Vertical cable
slot
➊
➋
➌
GA 32
antenna
Pole-mount
adapter
Vertical cable
slot
➊
➋
➌

   Find Your Products By Category